View HDMIULC6-4SC6_1248672.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HDMIULC6-4SC6
Ultra large bandwidth ESD protection
Main applications

HDMI ports at 1.65 Gb/s and up to 3.2 Gb/s IEEE 1394a, b, or c up to 3.2 Gb/s USB 2.0 ports up to 480 Mb/s (Hi-Speed) Ethernet port: 10/100/1000 Mb/s Video line protection SOT23-6L (JEDEC MO178AB)
Functional diagram
I/O1
1
Description
The HDMIULC6-4SC6 is a monolithic, application specific discrete device dedicated to ESD protection of the HDMI connection. It also offers the same high level of protection for IEEE 1394a and IEEE 1394b/c, USB 2.0, Ethernet links, and video lines. Its ultra high cutoff frequency (5.3 GHz) secures a high level of signal integrity. The device topology provides this integrity without compromising the complete protection of ICs against the most stringent ESD strikes.
6
I/O4 When used with an HDMI VBUS application, Pin 5 should not be connected to protect against backdrive current flow. I/O3
GND
2
5
I/O2
3
4
Benefits
Features

4 line 15 kV ESD protection Protects VBUS when applicable Ultra high bandwidth - no inluence on signal rise and fall times - maximised number of signal harmonics Very low leakage current: 0.5 A max. Fast response time compared with varistors SOT23-6L package RoHS compliant
ESD standards compliance guaranteed at device level, hence greater immunity at system level ESD protection of VBUS when applicable. High efficiency due to low residual voltage when confronted by an ESD surge Minimized rise and fall times for maximum data integrity Consistent D+ / D- signal balance: - Ultra low impact on intra-, inter-pair skew - Matching high bit rate HDMI requirements and ready for future evolution Low PCB space occupation - 9 mm maximum foot print Low leakage current for longer operation of battery powered devices Higher reliability offered by monolithic integration

Complies with these standards:
IEC 61000-4-2 level 4 - 15 kV air discharge - 8 kV (and up to 15 kV) contact discharge
Order code
Part Number HDMIULC6-4SC6 Marking DL46
July 2006
Rev 2
1/11
www.st.com
Characteristics
HDMIULC6-4SC6
1
Characteristics
Table 1.
Symbol VPP Tstg Tj TL Peak pulse voltage Storage temperature range Maximum junction temperature Lead solder temperature (10 seconds duration)
Absolute ratings
Parameter IEC 61000-4-2 air discharge IEC 61000-4-2 contact discharge MIL STD883C-Method 3015-6 Value 15 15 25 -55 to +150 125 260 Unit kV C C C
Table 2.
Symbol IRM VBR
Electrical characteristics (Tamb = 25 C)
Value Parameter Leakage current Breakdown voltage between VBUS and GND Test Conditions Min. VRM = 5 V IR = 1 mA IPP = 1 A, tp = 8/20 s Any I/O pin to GND 6 12 17 1 0.6 0.015 VR = 0 V, F = 1 MHz VR = 0 V, F = 825 MHz Capacitance variation between I/O 0.42 0.3 0.007 0.5 pF pF Typ. Max 0.5 A V V V Unit
VCL
Clamping voltage IPP = 5 A, tp = 8/20 s Any I/O pin to GND Capacitance between I/O and GND VR = 0 V, F = 1 MHz VR = 0 V, F = 825 MHz
Ci/o-GND
Capacitance variation between I/O Ci/o-GND and GND Ci/o-i/o Ci/o-i/o Capacitance between I/O
2/11
HDMIULC6-4SC6
Characteristics
Figure 1.
Line capacitance versus line voltage (typical values)
C(pF)
Figure 2.
Line capacitance versus frequency (typical values)
C(pF)
1.0
F=825MHz Vosc=500mVRMS VBUS OPEN Tj =25 C
1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 CI/O - GND
0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2
Vosc=30mVRMS Tj =25C VI-O/GND = 0V VBUS OPEN
CI/O - GND
Data line voltage (v)
0.1
0
CI/O - CI/O
F(MHz)
1 10 100 1000 10000
Figure 3.
Relative variation of leakage current versus junction temperature (typical values)
Figure 4.
Frequency response
S21(db)
Attenuation
IRM[Tj] / IRM[Tj=25C]
5 4
0
-2
3
2
-4
-6
Tj(C)
1 25 50 75 100 125
-8 100.0k 1.0M 10.0M 100.0M 1.0G
F(Hz)
3/11
Application examples
HDMIULC6-4SC6
2
Application examples
Figure 5. HDMI Digital single link application using HDMIULC6-4SC6
Host (Set Top Box, DVD player, PC)
HDMI
Tx0Tx0+
TMDS transmitter
Rx0Rx0+
Display (TV, flat panel, monitor, projector)
HDMI connectors
TMDS receiver
video
video
Tx1Multimedia controller
audio
Rx1Rx1+ Rx2Rx2+
Ctrl / status audio
Tx1+ Tx2Tx2+
controller
Ctrl / status
HDMIULC6-4SC6
TCTC+ TMDS links CEC SCL Vcc 5V SDA HPD Control links
HDMIULC6-4SC6
RCRC+ CEC SCL Vcc 5V SDA HPD
Figure 6.
T1/E1/Ethernet protection
Tx
SMP75-8 +VCC 100 nF
3 1 1 2 4 5
DATA TRANSCEIVER
Rx
SMP75-8
4/11
6
HDMIULC6-4SC6
Application examples
2.1
PCB layout considerations
For HDMI applications, VCC should not be connected. In this case the capacitor C in Figure 7. is not needed. Figure 7. PCB layout considerations (VCC connection is application dependent)
HDMI Connector Side
D+1 D-1 GND D+2 D-2
1
VCC
C = 100 nF
HDMIULC6-4SC6
A differential impedance of 100 must be respected in the layout. Both lines of the differential pair should have the same length. Figure 8. Footprint dimensions (in mm)
1.20 1.10
0.60
0.95
2.30
3.50
5/11
Technical information
HDMIULC6-4SC6
3
3.1
Technical information
Surge protection
The HDMIULC6-4SC6 is particularly optimized to perform ESD surge protection based on the rail to rail topology. The clamping voltage VCL can be calculated as follows: VCL+ = VTRANSIL + VF for positive surges VCL- = - VF with: VF = VT + Rd.Ip (VF forward drop voltage) / (VT forward drop threshold voltage) and VTRANSIL = VBR + Rd_TRANSIL . IP for negative surges
Calculation example
We assume that the value of the dynamic resistance of the clamping diode is typically: Rd = 0.5 and VT = 1.1 V. We assume that the value of the dynamic resisteance of the transil diode is typically Rd_TRANSIL = 0.5 and VBR = 6.1 V For an IEC 61000-4-2 surge Level 4 (Contact Discharge: Vg= 8 kV, Rg= 330 ), VBUS = +5 V, and, in first approximation, we assume that: Ip = Vg / Rg = 24 A. We find: VCL+ = +31.2 V VCL- = -13.1 V Note: The calculations do not take into account phenomena due to parasitic inductances.
3.2
Surge protection application example
If we consider that the connections from the pin VBUS to VCC, from I/O to data line, and from GND to PCB GND plane are two tracks 10 mm long and 0.5 mm wide, we can assume that the parasitic inductances, LVBUS, LI/O, and LGND, of these tracks are about 6 nH. So when an IEC 61000-4-2 surge occurs on the data line, due to the rise time of this spike (tr = 1 ns), the voltage VCL has an extra value equal to LI/O.dI/dt + LGND.dI/dt. The dI/dt is calculated as: dI/dt = Ip/tr = 24 A/ns for an IEC 61000-4-2 surge level 4 (contact discharge Vg = 8 kV, Rg = 330 The over voltage due to the parasitic inductances is: LI/O.dI/dt = LGND.dI/dt = 6 x 24 = 144 V By taking into account the effect of these parasitic inductances due to unsuitable layout, the clamping voltage will be: VCL+ = +31.2 + 144 +144 = 319.2 V VCL- = -13.1 - 144 -144 = -301.1 V We can reduce as much as possible these phenomena with simple layout optimization.
6/11
HDMIULC6-4SC6
Technical information
It's the reason why some recommendations have to be followed (see Section 3.3: How to ensure good ESD protection). Figure 9. ESD behavior: parasitic phenomena due to unsuitable layout
VCL+ VBUS Data line LI/O
ESD surge on data line
LI/O
di L VBUS dt
Vcc pin
L I/O
di di + L GND dt dt
POSITIVE SURGE
VF VTRANSIL
I/O pin
VCL
VTRANSIL +VF t
tr=1ns
GND pin
LGND
LGND
di dt
-VF
tr=1ns
t
VCL + = VTRANSIL + VF + L I/O VCL - = - VF - L I/O
di di + L GND dt dt di di - L GND dt dt
surge > 0
- L I/O
surge < 0
di di - L GND dt dt
NEGATIVE SURGE
VTRANSIL = VBR + Rd.Ip
VCL-
3.3
How to ensure good ESD protection
While the HDMIULC6-4SC6 provides a high immunity to ESD surge, an efficient protection depends on the layout of the board. In the same way, with the rail to rail topology, the track from data lines to I/O pins, from VCC to VBUS pin, and from GND plane to GND pin must be as short as possible to avoid over voltages due to parasitic phenomena (see Figure 9 and Figure 10 for layout considerations). Figure 10. ESD behavior: layout optimization Figure 11. ESD behavior: measurement conditions
ESD SURGE TEST BOARD IN OUT
Unsuitable layout
HDMIULC6- 4SC6
Vbus
Optimized layout
7/11
Technical information
HDMIULC6-4SC6
Figure 12. Remaining voltage after the HDMIULC6-4SC6 during positive ESD surge
Figure 13. Remaining voltage after the HDMIULC6-4SC6 during negative ESD surge
Note:
The measurements have been done with the HDMIULC6-4SC6 in open circuit.
IMPORTANT:
An important precaution to take is to put the protection device as close as possible to the disturbance source (generally the connector).
3.4
Crosstalk behavior
Figure 14. Crosstalk phenomena
RG1 Line 1 1 VG1 + 12VG2
VG1 RG2 Line 2
RL1
VG2
RL2
2VG2 + 21VG1
DRIVERS
RECEIVERS
The crosstalk phenomena is due to the coupling between 2 lines. The coupling factor (12 or 21) increases when the gap across lines decreases, particularly in silicon dice. In the example above the expected signal on load RL2 is 2VG2, in fact the real voltage at this point has got an extra value 21VG1. This part of the VG1 signal represents the effect of the crosstalk phenomenon of the line 1 on the line 2. This phenomenon has to be taken into account when the drivers impose fast digital data or high frequency analog signals in the disturbing line. The perturbed line will be more affected if it works with low voltage signal or high load impedance (few k).
8/11
HDMIULC6-4SC6 Figure 15. Analog crosstalk measurements
TEST BOARD NETWORK ANALYSER PORT 1
Technical information
NETWORK ANALYSER PORT 2 Vbus
Figure 15 gives the measurement circuit for the analog application. In usual frequency range of analog signals (up to 240 MHz) the effect on disturbed line is less than -45 dB (see Figure 16). Figure 16. Analog crosstalk results
0.00
dB
- 30.00
- 60.00
- 90.00
F (Hz)
- 120.00 100.0k 1.0M 10.0M 100.0M 1.0G
As the HDMIULC6-4SC6 is designed to protect high speed data lines, it must ensure a good transmission of operating signals. The frequency response (Figure 4.) gives attenuation information and shows that the HDMIULC6-4SC6 is well suitable for data line transmission up to 3.2 Gb/s.
9/11
Package information
HDMIULC6-4SC6
4
Package information
Table 3. SOT23-6L dimensions
DIMENSIONS REF.
E
Millimeters Min. Typ. Max. Min.
Inches Typ. Max. 0.057 0.004 0.051 0.02 0.008 0.120 0.069 0.037
A A1
e b e
D
0.90 0 0.90 0.35 0.09 2.80 1.50 0.95 2.60 0.10 0
1.45 0.035 0.10 0
A2 b c
A2
1.30 0.035 0.50 0.014 0.20 0.004 3.05 0.110 1.75 0.059
D E
c
H
A1 L
e H L
3.00 0.102 0.60 0.004 10 0
0.118 0.024 10
In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.
5
Ordering information
Ordering code HDMIULC6-4SC6 Marking DL46 Package SOT23-6L Weight 16.7 mg Base qty 3000 Delivery mode Tape and reel
6
Revision history
Date 28-Mar-2006 26-Jul-2006 Revision 1 2 Description of Changes First Issue Replaced technical information section.
10/11
HDMIULC6-4SC6
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
11/11

▲Up To Search▲

Price & Availability of HDMIULC6-4SC6

	To Download HDMIULC6-4SC6 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .